pp電鍍槽在運輸途中要注意哪些問題
未知, 2019-12-16 12:26, 次瀏覽
pp電鍍槽在運輸途中要注意哪些問題
What should be paid attention to in the transportation of PP electroplating tank
用戶在廠家購買到pp電鍍槽后要將設備運輸?shù)绞褂玫攸c(diǎn),通常這個運輸距離都不是很短,那么怎么樣在運輸途中保護pp電鍍槽不受損傷,下面就以pp電鍍槽中的pp電鍍槽為例,說一說在運輸設備中要注意哪些問題。
After the manufacturer purchases the PP plating bath, the user should transport the equipment to the place of use. Generally, the transportation distance is not very short. Then, how to protect the PP plating bath from damage during the transportation? Take the PP plating bath in the PP plating bath as an example, which problems should be paid attention to in the transportation equipment.
1、運送pp電鍍槽的專用拖管車,管子超長不得超越2M,裝車高度及層數滿足施工規范的需要。
1. The length of the special pipe tractor for transporting the PP electroplating tank shall not exceed 2m, and the loading height and number of layers shall meet the requirements of the construction specifications.
2、pp電鍍槽運送應根據工程部分的調度計劃進行,每車宜裝運同一種規范的管子,當管子運到指定地址卸車后,由運管人員和現場接納人員共同對pp電鍍槽進行檢查,填寫檢查記載。并移交有關栓驗,運送單據。
2. The delivery of PP electroplating tank shall be carried out according to the scheduling plan of the engineering part. Each truck should be loaded with pipes of the same specification. When the pipes are transported to the designated address for unloading, the transportation management personnel and on-site acceptance personnel shall jointly inspect the PP electroplating tank and fill in the inspection records. And hand over the relevant bolt inspection and delivery documents.
3、運管車輛有必要限速跋涉,避免急剎車,避免管子移位,損壞防腐層。
3. It is necessary to speed limit and trudge the pipe transport vehicles to avoid sudden braking, pipe displacement and damage to the anti-corrosion coating.
4、拖管車底部選用厚度不小于15MM的橡膠板或其柔性材料做軟墊屋,其寬度不得小于100MM。
4. Rubber plate with thickness no less than 15mm or its flexible material shall be selected as the soft cushion roof at the bottom of the trailer, and its width shall not be less than 100mm.
5、選用尼龍帶進行捆扎,捆扎用具接觸管子的部位要襯墊軟質材料。運送彎頭,彎管還要采用有用的固定辦法。
5. Nylon belt shall be used for binding, and soft materials shall be padded at the position where the binding appliance contacts the pipe. When transporting elbows, useful fixing methods shall be adopted.
為了能將pp電鍍槽完***的運輸?shù)娇蛻舻氖种?,廠家在發車時要仔細檢查那些保護包裝是否完整,是否達到了要求。
In order to transport the PP plating bath to the customer's hands in good condition, the manufacturer shall carefully check whether the protective packages are complete and meet the requirements when departure.